Samsung HT-E5500W Blu-ray System MICOM Driver
Blu-ray Player Will Not Connect to the Internet via Wi-Fi. For your Blu-ray READ MORE. 4 of 12 Top Solutions for Blu-ray Home Theater (HT-BD2E Series). Blu-ray Home Theater (HT-CW Series) edit. Firmware. Blu-ray Player Will Not Connect to the Internet via Wi-Fi. For your Blu-ray player to. Blu-ray Home Theater. System Model Name. HT-E Model Code After replacing the Main PCB and System Micom (IC23), the region code should be.
|Supported systems:||Windows XP, Windows Vista, Windows 7, Windows 7 64 bit, Windows 8, Windows 8 64 bit, Windows 10, Windows 10 64 bit|
|Price:||Free* [*Free Registration Required]|
Samsung HT-E5500W Blu-ray System MICOM Driver
Samsung HT C5500
Product Specification Product Feature Troubleshooting Checkpoints by Error Mode Schematic Diagram Overall Block Diagram PrecautionFollow these safety instructions while servicing the ESD to prevent damage and to protect against potential hazards such as electrical shock and X-rays. When reinstalling the chassis and its assemblies, be sure to restore all of the protective devices, including the control knobs and the compartment covers. Make sure that there are no cabinet Samsung HT-E5500W Blu-ray System MICOM through which people particularly children can make contact with dangerous internal components.
Never alter or add to the mechanical or electrical design of the unit.
Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard.
Also, any design changes or additions will void the manufacturers warranty. Leakage Current Hot Check Fig. Do not use an isolation transformer during this test. With the units power switched from the ON to the OFF position, measure the current between a known Samsung HT-E5500W Blu-ray System MICOM and all exposed metal parts. Known Grounds - Earth Known Metal parts - screwheads, metal cabinets, etc.
Insulation Resistance Cold Samsung HT-E5500W Blu-ray System MICOM If there is no return path, the measured resistance should be infinite. If the resistance is outside these limits, a shock hazard might exist. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications.
Smart Home Theater (HT-E Series) Owner Information & Support Samsung US
Always determine the cause of damage or overheating, and correct any potential hazards7. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring.
Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that no wires or components touch thermally hot parts. Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection. These safety features and Samsung HT-E5500W Blu-ray System MICOM protection they give might be lost if the replacement component differs from the original--even if the replacement is rated for higher voltage, wattage, etc.
Components that are critical for safety are indicated in the circuit diagram by shading, or. Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.
A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards. Samsung Electronics Precaution ServicingPrecautions1. Servicing precautions are printed on the cabinet.
Download Drivers Samsung HT-E Home Theater Firmware
Always unplug the units AC power Samsung HT-E5500W Blu-ray System MICOM from the AC power source before attempting to: Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring may be clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.
After servicing, always check that the screws, components and wiring have been correctly reinstalled.
Make sure that the portion around the serviced part has not been damaged. Check the insulation between the blades of the AC plug and accessible conductive parts examples: Disconnect the power cord from the AC source. Connect an insulation resistance meter V to the blades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts see above should be greater than 1 megohm. Do not apply AC power to the unit or any of its assemblies unless all solid-state heat sinks are correctly installed. Always connect a test instruments ground lead to the instrument chassis ground before connecting the positive lead; always remove the instruments ground lead last.
- Home Theater System (HT-J) Owner Information & Support Samsung US
- Blu-ray Home Theater (HT-CW Series) Owner Information & Support Samsung US
- My nadoelodelatdori