Weigl Works ProCommander 2 Controller Driver
Flashing the Screen Address on LED Controller Boards 2. Insert the USB stick into front of the Pro Commander LTC. All content . Weigl PRO I/O. A1 *Note* The show must be in the shut down position for the diagnostics to work correctly. Supported DMX Dongle Devices That Will Work With Venue Magic Show Control Inc. to be sold as an option with the VenueMagic Show Control Software. ENTTEC DMX USB Pro & USB Pro 2 WeiglWorks WEMC-1 ProCommander. I've been evaluating the Weigl ProCommander 2 and Venue Magic SC+ software for animatronic control, and together they look like a solid.
|Supported systems:||Windows XP (32/64-bit), Windows Vista, Windows 7, Windows 8.1, Windows 10|
|Price:||Free* [*Free Registration Required]|
Weigl Works ProCommander 2 Controller Driver
The show computer connected to the interface communicates with the show controller over UDP. The IP address for the show controller is These ASCII commands are stored as strings and can be sent over UDP Weigl Works ProCommander 2 Controller the show controller when we want to invoke a particular show or any particular behaviour.
Programming with Weigl System
We also integrated with the existing show control system in the Castle of Miracles. This allowed us to breathe in new life into an old Weigl Works ProCommander 2 Controller. While integrating, we wanted to ensure that the staff controlling Tom Foolery was able to start the Father Time show. On pin 9 of the pin connector blocks the internal voltage of the power supply is brought out.
Timeline/Show Trigger by Extrnal control Pangolin Forum
Pin 9 of the top row is permanently connected. Pin 9 of the bottom row is connected to the common cathode of the output driver. The internal voltage of the power supply can be connected to each of the pin 9, by closing the Jumpers K12 and K14 see marking on the picture below.
- Programming with Weigl System – miracle_workshop_
- Timeline/Show Trigger by Extrnal control
- ProCommander 2
- Introducing Showforge
- Supported Devices that work with Venue Magic
ProCommander manual Version 24 The maximum available current depends on the used power supply, but must not exceed mA. For proper functions of the ProCommander if the audio amplifier is used, a current consumption of about 1 ampere must be calculated.
To ensure proper function of the ProCommander, when using the supplied power must be part of the load is not more than mA. The voltage is dependent on the power supply voltage minus the loss of internal reverse polarity protection diode.
Pin 10 of the four pin connectors is connected Weigl Works ProCommander 2 Controller the internal device ground. If the ProCommander is hard-faced with relays the first eight Inputs and the first 8 Open-Collector Outputs are not available. Each of the relay-contacts is attached with the first block of the two pin connectors. Pins 1 to 8 of the upper row are connected with the relay 1 to 4 and the pins of the lower row with the relay 5 to 8.
ProCommander manual Version 26 4. Serial port configuration The factory setting of the three serial interfaces is Baud, 8N1.
These interface parameter have to be chosen, if the Pro- Commander should be configured with a terminal program Configuration via serial interface RS The current settings can be requested with the command!? For that you have to connect the ProCommander with a serial interface of the computer and start the ProCommander configurator.
WEMC-1. ProCommander. Version 1.01
The program does not have to be installed. Just copy all files of the ZIP-archive into a new folder and start the program with double-click on WemcConfig. If you verify the button "Scan for Devices" the affiliated device will be found automatically.
Through clicking on the listed devices the current settings will be shown in the "Console"-window. Then you can change the IP address, the port and the subnet mask and save it in the device. The new parameter will be saved permanently in ProCommander with pressing the button "Save Permanently".
By click on "Save Temporarily" the changed settings will be saved temporarily. If the device is switched off, the original data will be activated again. If your computer does not have a serial interface, the Weigl Works ProCommander 2 Controller can also be made through a network. Here is important, that the IP address of the computer in combination with the subnet mask matches with the factory settings of the ProCommander.